Type EK-JZ

BVDAX for smoke extraction operation with frequency converter, CE certified in accordance with EN 12101-3 Temperature

For mechanical smoke extract systems and pressure differential systems

Maximum size, maximum performance

B = 1.20 m, H = 2.03 m

Minimum leakage with both high and low temperatures due to 2-component sealing system

Vertical damper blade alignment possible

EK-JZ

For mechanical smoke extract systems and pressure differential systems, as well as for providing additional supply air

Rectangular smoke control dampers with ventilation function, low installation depth and large cross section for heat and smoke exhaust with mechanical smoke extract systems, for the provision of additional supply air and for use in pressure differential systems

Nominal sizes 200 × 230 – 1200 × 2030 mm, for smoke gas flow rates up to 29230 m³/h or 105235 m³/h at 12 m/s, upstream velocities up to 20 m/s possible
Simple and quick installation in and on components
Casing, damper blades and actuator encasing made of calcium silicate
Pressure level 2 (operating pressure -1000 to 500 Pa)
Automatic release (AA), option of manual override (MA)
For smoke extract ducts from 35 mm wall thickness
Closed blade air leakage to EN 1751, class 3
Casing air leakage to EN 1751, class C

Optional equipment and accessories

Cover grille (various constructions)
Connecting subframe for calcium silicate and sheet steel smoke extract ducts
Integration into the central BMS with TROXNETCOM
Coating for use in exterior walls
C_mod = for smoke extract and ventilation in combined systems, which allows for pneumatic volume flow rate balancing as the damper blade can take intermediate positions
Installation accessories

General information

Application

Smoke control damper, with CE marking and declaration of performance, for heat and smoke exhaust with mechanical smoke extract systems
Can be used for the provision of fresh air (additional supply air) to mechanical smoke extract systems
Can be used in pressure differential systems
Can be used for ventilation if the mechanical smoke extract system has been certified (general building inspectorate licence) for use with combined systems
Integration into the central BMS with TROXNETCOM

Special features

C_mod for smoke extract and ventilation in combined systems, which allows for pneumatic volume flow rate balancing as the damper blade can take intermediate positions
Complies with the requirements of EN 12101-8
Tested to EN 1366-2 and 1366-10 for fire resistance properties
Closed blade air leakage to EN 1751, Class 3, and casing leakage to EN 1751, Class C
Low sound power level and differential pressure
Any airflow direction
Manual release is also possible using TROXNETCOM
Long-time testing to EN 1366-10, with 20000 OPEN/CLOSE cycles

Parts and characteristics

Installation orientation is independent of the airflow direction
Pressure level 2 (operating pressure -1000 to 500 Pa)
For automatic and manual release
Smoke control damper with ventilation function

Classification

EI 120/90 (v_edw-h_odw, i↔o) S1000 C_mod HOT 400/30 MA multi

Nominal sizes

200 × 230 – 1200 × 2030 mm
Casing lengths L = 250 mm

Attachments 1

Connecting subframe for calcium silicate and sheet steel smoke extract ducts
Cover grille – crimped wire mesh or square perforated metal plate
Cover grille – grille with straight or slanted blades

Attachments 2

Open/Close actuators with 24 V AC/DC or 230 V AC supply voltage
Network modules for the integration with AS-i networks
Network modules for other standard bus systems

Optional products

TROXNETCOM

TROX-X smoke exhaust fans from the X-FANS subassembly

TROX-X smoke exhaust fans from the X-FANS subassembly

Smoke exhaust fan for roof installation BVDAX/ BVD
Smoke exhaust fan for wall installation BVW/ BVWAXN
Smoke exhaust centrifugal fan BVREH /BVRA
Smoke extract jet fans BVGAX/BVGAXN

All smoke exhaust fans are tested to EN 12101-3, for F200/F300/F400 and F600, depending on the type. With CE marking, declaration of performance and application approval for the German market.

Speed adjustment for smoke exhaust fans

Certified frequency inverter unit X-FANS control
Safe and precise speed adjustment of smoke exhaust fans both in one-zone and in multi-zone systems.

Construction features

Rectangular construction
Smoke control damper actuator controlled by reversible open/close actuator
Remote control with actuator
Suitable for the connection of cover grilles or connecting subframes

Materials and surfaces

Casing, damper blade and actuator encasing made of calcium silicate
Brass bearings
Blade shafts, drive arm and shaft bearing made of galvanised steel

Standards and guidelines

Construction Products Regulation
EN 12101-8 Smoke and heat control systems – Smoke control dampers
EN 1366-10 Fire resistance tests for service installations – Smoke control dampers
EN 1366-2 Fire resistance tests for service installations – Fire dampers
EN 13501-4 Fire classification of construction products and building elements using data from fire resistance tests
EN 1751 Ventilation for buildings – Air terminal devices

Maintenance

Smoke control dampers must be operational at all times and must be maintained regularly so that they provide the required services.
Maintenance is required at least every 6 months
A maintenance report must be created; documents must be kept for reference
The functional reliability of the smoke control damper must be tested at least every six months; this has to be arranged by the owner of the smoke extract system; functional tests must be carried out in compliance with the basic maintenance principles stated in EN 13306 and DIN 31051. If two consecutive tests, one 6 months after the other, are successful, the next test can be conducted one year later
Depending on where dampers are installed, country-specific regulations may apply.
For details on maintenance and inspection, refer to the installation and operating manual.

Technical information

Function, Quick sizing, Specification text, Order code

Schematic illustration

① Casing

② Blades

③ Blade tip seal (special profile seal)

④ Side seal

⑤ Travel stop, bottom

⑥ Actuator

⑦ Cover fixing

⑧ Rating plate

⑨ Cover of the actuator encasing

⑩ Handle (to remove the cover)

⑪ Actuator encasing

⑫ Travel stop, top

Smoke control dampers are used in mechanical smoke extract systems. They are used for extracting smoke gases and for providing additional supply air to one or more fire compartments. The dampers are made of calcium silicate panels and are opened by an encased actuator; when smoke is detected, the actuator is triggered by a signal either from a duct smoke detector or from a fire alarm system. Smoke control dampers have two safe positions: open and closed. In the case of fire-resistant smoke control dampers for multiple compartments, the safe position is either "open" or "closed", depending on the fire site and the path of the smoke to be extracted. If the safe position is 'open', the free area must be maintained even in the event of a fire. The blades of EK-JZ move to the defined safe position upon receiving an automatically or manually triggered control signal. According to the specified time-temperature curve, the EK-JZ can still fully open or close after 25 minutes (MA, manual release). With the EK-JZ product type, it is also possible to change the position for modulation uses (Cmod) and thus a pneumatic adjustment in the ventilation operation of a combined system by moving to intermediate positions of the damper blade field. Regular maintenance of the smoke control damper is required to ensure its functional reliability.

Installation type A, in a duct

Ducted on both sides, any airflow direction

Installation type B, additional supply air

Quick sizing tables in Easy Product Finder provide a good overview of the volume flow rates for different airflow velocities as well as of differential pressures
Precise values based on project-specific data can be determined with our Easy Product Finder design software
You will find the Easy Product Finder on our website
www.trox.de/mytrox/auslegungsprogramm-easy-poduct-finder-182e16348fac3d33

Specification text

Rectangular or square smoke control dampers to product standard EN 12101-8, tested to EN 1366-10 and EN 1366-2, for use in smoke extract systems. Smoke control dampers are not only used for the exhaust of smoke, heat and combustion products from a fire compartment, but also for the controlled removal of dangerous and toxic combustion and fire suppression gases. EK-JZ smoke control dampers can also be used in pressure differential systems and as pressure relief dampers in gas fire extinguishing systems. Also for extracting smoke gases and for providing additional supply air for the mechanical smoke extract of one or more fire compartments and in all listed systems of the same type that need to fulfil modulation applications. EK-JZ can be used in combined smoke exhaust systems which have been approved for controlled ventilation. The fire-resistant smoke control damper for multiple compartments is suitable for installation in and on fire-resistant smoke extract ducts or smoke extract shafts and in fire-resistant standard supporting constructions. The control of open/close actuators can be implemented with control modules that are factory wired or with bus modules inside the temperature-resistant actuator encasing.

Parts and characteristics

Installation orientation is independent of the airflow direction
Pressure level 2 (operating pressure -1000 to 500 Pa)
For automatic and manual release
Smoke control damper with ventilation function

Construction features

Rectangular construction
Smoke control damper actuator controlled by reversible open/close actuator
Remote control with actuator
Suitable for the connection of cover grilles or connecting subframes

EK-JZ

–

1200 × 2030

B24A

P1 - RAL...

1 Type
EK-JZ
Smoke control damper according to EN 12101-8

2 Actuator encasing As seen from the operating side
R = Right (as standard)
L = Left

3 Damper blade alignment
No entry required = Horizontal damper blade alignment (standard)
V = Vertical damper blade alignment

4 Coating
No entry required = None (standard)
C1 = Promat SR impregnation

5 Country of destination
DE Germany
CH Switzerland
AT Austria
PL Poland
and others

6 Nominal size [mm]
B × H (B in 50 mm increments; H in 200 mm increments)
From 200 × 230 to 1200 × 2030

7 Accessories 1
No entry required = None (standard)
01 Fixing tabs (quantity depends on B × H)

Only in the case of horizontal damper blade alignment
02 Lower HT seal
03 Lower HT seal and fixing tabs (quantity depends on B × H)
04 Side HT seal
05 Lower and side HT seals
06 Lower and side HT seals and fixing tabs (quantity depends on B × H)
07 Side HT seal and fixing tabs (quantity depends on B × H)
08 Upper (special) HT seal
09 Upper (special) and side HT seals
10 Upper (special) HT seal and fixing tabs (quantity depends on B × H)
11 Upper (special) and side HT seals and fixing tabs (quantity depends on B × H)
12 Ceiling fixing tabs (double quantity depends on B × H)

Only in the case of vertical damper blade alignment
13 Upper (special) HT seal
14 Side and upper (special) HT seals
15 Upper (special) HT seal and fixing tabs (quantity depends on B × H)
16 Upper (special) and side HT seals and fixing tabs (quantity depends on B × H)

8 Attachments 1
No entry required: None
F – Connecting subframe, galvanised steel, cover grille
A – Crimped wire mesh, 20 × 20, galvanised steel
B – Square perforated metal plate, 10 × 10, galvanised steel
C – Grille with slanted blades made of aluminium
D – Grille with slanted blades, aluminium, additionally with crimped wire mesh, 20 × 20, galvanised steel
E – Grille with slanted blades, aluminium, additionally with welded wire mesh, 6 × 6 mm, galvanised steel

Character 1 refers to the operating side, without attachment on operating side: 0
Character 2 defines installation side, without attachment on installation side: 0
Example: FA: Connecting subframe on the operating side, crimped wire mesh 20 × 20 on the installation side
Any combination is possible

9 Attachments 2
Actuator
B24 – Actuator, Belimo, 24 V AC/DC
B24SR – Actuator, Belimo, 24 V AC/DC, continuous control with operating range of 2 – 10 V DC, ventilation function C_mod¹
B230 – Actuator, Belimo, 230 V AC
Actuator combined with TROX control module
B24A – Actuator, Belimo, 24 V AC/DC with TROXNETCOM control module AS-EM/EK ²
B24AS – Actuator, Belimo, 24 V AC/DC with TROXNETCOM control module AS-EM/SIL2 ²
B24AM – Actuator, Belimo, 24 V AC/DC with TROXNETCOM control module AS-EM/M, for function C_mod¹

Other communication modules:
B24BKNE – Actuator, Belimo, 24 V AC/DC, Belimo communication and power supply unit BKNE230-24
B24C – Actuator, Belimo, 24 V AC/DC, BV-Control communication and power supply unit with SLC^®technology BC24 G2)
B24D – Actuator Belimo, 24 V AC/DC, Agnosys fire damper smoke control damper module BRM-10-F-ST
B230D – Actuator Belimo, 230 V AC, Agnosys fire damper and smoke control damper module BRM-10-F

¹ Function C_mod for damper blade in intermediate position
² The AS-i system is based on the industrial standard AS-Interface

10 Surface finish (attachments 1)
No entry required: None (standard)
P1 Powder-coated, specify RAL CLASSIC colour
PS Powder-coated, DB colour …
Gloss level:
RAL 9010 50 %
RAL 9006 30 %
All other RAL colours 70 %

Order example: EK-JZ-R-V-C1/DE/800 × 1030/14/A0/B24A/P1-RAL9010-50%

Actuator encasing	Operating side, on the right
Damper blade alignment	Vertical
Coating	Impregnation
Country of destination	Germany
Nominal size	800 × 1030 mm
Accessories 1	Side and upper (special) HT seals
Attachment 1	Cover grille on the operating side
Attachment 2	TROX actuator Belimo, with TROXNETCOM control module AS-EM/EK
Surface attachment	P1-RAL9010 50 % cover grille with powder coating, RAL 9010, pure white, gloss level 50 %

Dimensions, Product details

a Installation side
b Operating side

① Subframe for connection to the duct (steel, operating side only and or installation side, optional)

② Keep clear to provide access to the actuator encasin

Weights [kg], width 200 – 650 mm

L	H	B
L	H	200	250	300	350	400	450	500	550	600	650
250	230	21	22	23	24	25	27	28	29	30	31
250	430	29	31	32	33	35	36	38	39	41	42
250	630	37	39	41	43	44	46	48	50	51	53
250	830	46	48	50	53	54	56	58	61	62	64
250	1030	54	56	59	61	63	66	68	70	73	75
250	1230	62	65	67	70	73	75	78	81	83	86
250	1430	71	73	76	79	82	85	88	91	94	97
250	1630	79	82	85	88	92	95	98	101	105	108
250	1830	87	91	94	98	101	105	108	112	115	119
250	2030	95	99	103	107	111	114	118	122	126	130

Weights [kg], width 700 – 1200 mm

L	H	B
L	H	700	750	800	850	900	950	1000	1050	1100	1150	1200
250	230	32	34	35	36	37	38	39	40	42	43	44
250	430	44	45	47	48	49	51	52	54	55	57	58
250	630	55	57	58	60	62	64	65	67	69	71	72
250	830	66	69	70	72	75	77	78	80	83	85	87
250	1030	77	80	82	84	87	89	91	94	96	98	101
250	1230	89	91	94	97	99	102	104	107	110	112	115
250	1430	100	103	106	109	112	115	117	120	123	126	129
250	1630	111	114	118	121	124	127	130	134	137	140	143
250	1830	122	126	129	133	136	140	143	147	150	154	158
250	2030	134	137	141	145	149	153	156	160	164	168	172

Installation and commissioning

Installation on/in concrete or masonry shaft walls
Installation in lightweight partition walls
Installation in shaft walls that are covered on one side
Installation in or on tested, fire-resistant vertical or horizontal smoke extract ducts
Installation in fire-resistant REI 120 or EI 120 walls
For smoke extract ducts made of calcium silicate from 35 mm wall thickness
For sheet steel smoke extract ducts
After installation the damper must remain accessible for inspection, cleaning and repair
Connected smoke extract ducts must have an inspection access
Mechanical smoke extract systems require that the power supply is maintained even in the event of a fire

Smoke control dampers must be installed, connected and attached according to the operating and installation manual

Accessories, Attachments 1&2, Technical data, Building Management System (BMS), Nomenclature

Accessories

No entry required = None (standard)
01 Fixing tabs (quantity depends on B x H)

Only in the case of horizontal damper blade alignment
02 Lower HT seal
03 Lower HT seal and fixing tabs (quantity depends on B x H)
04 Side HT seal
05 Lower and side HT seals
06 Lower and side HT seals and fixing tabs (quantity depends on B x H)
07 Side HT seal and fixing tabs (quantity depends on B x H)
08 Upper (special) HT seal
09 Upper (special) and side HT seals
10 Upper (special) HT seal and fixing tabs (quantity depends on B x H)
11 Upper (special) and side HT seals and fixing tabs (quantity depends on B x H)
12 Ceiling fixing tabs (double quantity depends on B x H)

Only in the case of vertical damper blade alignment
13 Upper (special) HT seal
14 Side and upper (special) HT seals
15 Upper (special) HT seal and fixing tabs (quantity depends on B x H)
16 Upper (special) and side HT seals and fixing tabs (quantity depends on B x H)

ATTACHMENTS 1

Connecting subframes and cover grilles

Operating side	Installation side	Order code
Connecting subframe	–	F0
–	Connecting subframe	0F
Connecting subframe	Connecting subframe	FF
Cover grille A	–	A0
–	Cover grille A	0A
Cover grille A	Cover grille A	AA
Cover grille B	–	B0
–	Cover grille B	0B
Cover grille B	Cover grille B	BB
Cover grille C	–	C0
–	Cover grille C	0C
Cover grille C	Cover grille C	CC
Cover grille D	–	D0
–	Cover grille D	0D
Cover grille D	Cover grille D	DD
Cover grille E	–	E0
–	Cover grille E	0E
Cover grille E	Cover grille E	EE

A: Crimped wire mesh, 20 × 20 × 1.8 mm, galvanised steel (AG-E)
B: Square perforated metal plate, 10 × 10 mm, galvanised steel (AG-E)
C: Grille with slanted blades, aluminium (ALG-E)
D: Grille with slanted blades, aluminium, additionally with crimped wire mesh, 20 × 20 x 1.8 mm, galvanised steel (ALG-E)
E: Grille with slanted blades, aluminium, additionally with welded wire mesh, 6 × 6 mm, galvanised steel (ALG-E)
Any combination is possible

Attachments 2

Application

Open/close actuators for the opening and closure of smoke control dampers, with automatic (AA) or manual release (MA).
With integral limit switches for capturing the end positions
Override control for up to 25 minutes
Ambient temperature for normal operation: -30 to 50 °C, up to 95%, without temperatures below the dew point, no condensation (EN 60730-1)
Two integral limit switches with volt-free contacts can indicate the damper blade position (OPEN and CLOSED)
The connecting cables of the 24 V actuator are fitted with plugs, which ensure quick and easy connection to the TROX AS-i bus system
The connecting cable of the 230 V AC actuator is fitted with wire end ferrules

Variants

B24

24 V AC/DC supply voltage
BEN24-ST TR: Torque 15 Nm
BEE24-ST TR: Torque 20 Nm
BE24-12-ST TR: Torque 40 Nm

B230

Supply voltage 230 V AC
BEN230 TR: Torque 15 Nm
BEE230 TR: Torque 25 Nm
BE230-12 TR: Torque 40 Nm

B24-SR

BEN24-SR: Torque 15 Nm
BEE24-SR: Torque 25 Nm

The torque required to operate the smoke control damper depends on the size which is why the actuator type cannot be chosen freely.

Installation information

Feeding the electric connecting cable through the actuator encasing requires a drilled hole of the exact size (Ø max. + 1 mm)
A wire clamping bracket is required
For details on maintenance and inspection, refer to the installation and operating manual.

Wiring example 24 V AC / DC

① Switch for opening and closing, to be provided by others
② Indicator light for CLOSED position, to be provided by others
③ Indicator light for OPEN position, to be provided by others

Wiring examples, Technical data

Actuator	BEN24-ST	BEE24-ST	BE24-ST
Supply voltage (AC)	AC 19.2 – 28.8 V, 50/60 Hz
Supply voltage (DC)	DC 21.6 – 28.8 V, 50/60 Hz
Power consumption – when running	3 W	2.5 W	12 W
Power consumption – when idle	0.1 W		0.5 W
Power rating for cable sizing	Imax. 8.2 A at 5 ms
Torque	15 Nm	25 Nm	40 Nm
Run time for 90°	< 30 s
Limit switch contacts	2 × EPU
Switching current	1 mA – 3 A (0.5 A inductive), AC 250 V		1 mA – 6 A (0.5 A inductive), AC 250 V
Limit switch – open	5°		3°
Limit switch – close	80°		87°
Connecting cable – actuator	Cable 1 m, 3 × 0.75 mm², halogen-free
Connecting cable – limit switches	Cable 1 m, 6 × 0.75 mm², halogen-free
IEC protection class	III safety extra low voltage (SELV)
Protection level	IP 54
EC conformity	CE according to 2014/30/EU Low Voltage Directive CE according to 2014/35/EU
Operating temperature	-30 to 55 °C
Weight	0.9 kg	1.1 kg	2.7 kg

Actuator	BEN230 TR	BEE230 TR	BE230 TR
Supply voltage (AC)	AC 198 – 264 V, 50/60 Hz
Power consumption – when running	4 W	3.5 W	8 W
Power consumption – when idle	0.4 W		0.5 W
Power rating for cable sizing	Imax. 4 A at 5 ms		Imax. 7.9 A at 5 ms
Torque	15 Nm	25 Nm	40 Nm
Run time for 90°	< 30 s
Limit switch contacts	2 × EPU
Switching current	1 mA – 3 A (0.5 A inductive), AC 250 V		1 mA – 6 A (0.5 A inductive), AC 250 V
Limit switch – open	5°		3°
Limit switch – close	80°		87°
Connecting cable – actuator	Cable 1 m, 3 × 0.75 mm², halogen-free
Connecting cable – limit switches	Cable 1 m, 6 × 0.75 mm², halogen-free
IEC protection class	II reinforced insulation
Protection level	IP 54
EC conformity	CE according to 2014/30/EU Low Voltage Directive CE according to 2014/35/EU
Operating temperature	-30 to 55 °C		-30 to 50 °C
Weight	0.9 kg	1.1 kg	2.7 kg

Actuator	BEN24-SR	BEE24-SR
Supply voltage (AC)	AC 19.2 – 28.8 V, 50/60 Hz
Supply voltage (DC)	DC 21.6 – 28.8 V, 50/60 Hz
Power consumption – when running	3 W
Power consumption – when idle	0.3 W
Power rating for cable sizing	Imax. 8.2 A at 5 ms
Torque	15 Nm	25 Nm
Run time for 90°	< 30 s
Limit switch contacts	2 × EPU
Switching current	1 mA – 3 A (0.5 A inductive), AC 250 V
Limit switch – open	5°
Limit switch – close	80°
Connecting cable – actuator	Cable 1 m, 4 × 0.75 mm², halogen-free
Connecting cable – limit switches	Cable 1 m, 6 × 0.75 mm², halogen-free
IEC protection class	III safety extra low voltage (SELV)
Protection level	IP 54
EC conformity	CE according to 2014/30/EU Low Voltage Directive CE according to 2014/35/EU
Operating temperature	-30 to 55 °C
Weight	1.1 kg	0.9 kg

Interfaces to higher level systems

TROX fire and smoke protection systems have standardised interfaces for central building management systems. In the simplest case, the interface consists of discrete signalling contacts that connect the alternating inputs and outputs of TROX systems and other building components.

Control and communication modules for smoke control dampers

Order characteristic	B24A	B24AS	B24AM	B24BKNE	B24C	B230D	B24D
Module type	AS-EM/EK	AS-EM/SIL2	AS-EM/M	BKNE230-24	BC24	BRM-10-F	BRM-10-F-ST
EK2-EU	×	×	×	×	×	×	×
EK-JZ	×	×	×	×	×	×	×

Note: The smoke control dampers, actuators and communication modules described have each been verified by the manufacturer as a unit in terms of fire protection and may therefore only be used in such constellations.

B24A – AS-EM/EK

Application

Module for the control of smoke control dampers
Capturing damper blade positions OPEN and CLOSED
Actuators can be started even without controller communication
LEDs for OPEN and CLOSED positions; monitoring of run time errors
Integral AS-Interface slave
Monitoring of signal reception
Master can be used to monitor the run time of the damper blade actuator
Supply voltage of the module and the 24 V DC actuator using AS-Interface ( 2-wire control)
Plug-in connection for Belimo actuators (factory mounted and wired)

Use

B24A – Mounted to the smoke control damper

Description	AS-EM/EK
Electrical design	4 inputs/3 outputs
Output function	PNP transistor
Supply voltage	26.5 – 31.6 V DC
Current consumption, including actuator	450 mA
Inputs
Switching	DC PNP
Sensor voltage supply	AS-i
Voltage range	18 – 30 V AC
With short circuit protection	Yes
Switching level – high signal 1	10
Input current high/low	> 7 mA/< 2 mA
Input characteristic	IEC 61131-2 Type 2
Outputs, PNP
Galvanically isolated	No
Max. current load per output	400 mA per output/400 in total (from AS-i)
Outputs, relay
Galvanically isolated	Yes
Maximum voltage	32 V
Max. current load	500 mA
Ambient temperature	-5 to 75 °C
Protection level, IEC protection class	IP 42
AS-i profile	S-7.A.E
I/O configuration	7 Hex
ID code	7 Hex
EMC	EN 61000-6-2; EN 61000-6-3

B24AS – AS-EM/SIL2

Application

Module for the control of smoke control dampers
Capturing damper blade positions OPEN and CLOSED
Approved up to SIL2 to IEC/EN 61508
Integral AS-Interface slave
Monitoring of signal reception
Master can be used to monitor the run time of the damper blade actuator
Connection with terminals
Supply voltage of the module and the 24 V DC actuator using AS-Interface (2-wire control)
Plug-in connection for Belimo actuators (factory mounted and wired)

Use

B24AS – Mounted to the smoke control damper

Description	AS-EM/SIL2
Supply voltage	26.5 – 31.6 V DC
Current consumption	< 400 mA from AS-i
Max. current load per output	340 mA
Max. current load per module	340 mA
Status LED
AS-i power	1 × green
PeripheralFault	1 × red, blinking
ComError	1 × red, static
Output Q0	1 × yellow (DO0)
Output Q1	1 × yellow (DO1)
Input status LED SI-1	1 × yellow
Input status LED SI-2	1 × yellow
Input status DI0	1 × yellow (DI0)
Input status DI1	1 × yellow (DI1)
Input status DI2	1 × yellow (DI2)
Binary inputs	2 outputs with transistor (typically 24 V DC from AS-i, voltage range 18 – 30 V)
Operating temperature	-20 to 70 °C
Storage temperature	-20 to 75 °C
Protection level, IEC protection class	IP 54
Casing material	Plastic
AS-i profile	S-7.B.E (Safety at Work) and S7.A.E (motor module)
EMC	EN 61000-6-2; EN 61000-6-3

B24AM – AS-EM/M

Application

Module for the control of smoke control dampers with CmodFunction:
Capturing the damper blade end positions (CLOSED and OPEN)
Time-controlled selection of 13 intermediate positions of the damper blade (opening angle between 7° – 90°)
Actuators can be started even without controller communication
Emergency position can be set (OPEN or CLOSED)
LEDs for OPEN and CLOSED positions; monitoring of run time errors
Integral AS-Interface slave
Monitoring of signal reception
Master can be used to monitor the run time of the damper blade actuator
Supply voltage of the module and 24 V DC actuator using AS-Interface (2-wire control)
Plug-in connection for Belimo actuators

Use

B24AM – Mounted to the smoke control damper

Description	AS-EM/M
Electrical design	4 inputs/3 outputs
Output function	PNP transistor
Supply voltage	26.5 – 31.6 V DC
Current consumption, including actuator	450 mA
Inputs
Switching	DC PNP
Sensor voltage supply	AS-i
Voltage range	18 – 30 V AC
With short circuit protection	Yes
Switching level – high signal 1	10
Input current high/low	> 7 mA/< 2 mA
Input characteristic	IEC 61131-2 Type 2
Outputs, PNP
Galvanically isolated	No
Max. current load per output	400 mA per output/400 in total (from AS-i)
Outputs, relay
Galvanically isolated	Yes
Maximum voltage	32 V
Max. current load	500 mA
Ambient temperature	-5 to 75 °C
Protection level, IEC protection class	IP 42
AS-i profile	S-7.A.E
I/O configuration	7 Hex
ID code	7 Hex
EMC	EN 61000-6-2; EN 61000-6-3

B24BKNE – Communication module

Application

Communication and power supply unit for 24 V actuators in smoke extract applications, status LEDs, retention of the damper control input signal, 230 V AC connection, 1 m cable, free of halogens

Use

B24BKNE – BKNE230-24 communication module

Description	BKNE230-24
Nominal voltage	230 V AC 50/60 Hz
Functional range	198 – 264 V AC
Rating	19 VA (including actuator)
Power consumption	10 W (including actuator)
Length / cross section	On the actuator = 1 m, 3 (6*) × 0.75 mm² (free of halogens)
IEC protection class	II (protective insulation)
Ambient temperature	-30 to 50 °C
Storage temperature	-40 to 80 °C
Protection level	IP 54
EC conformity	EMC to 89/336/EEC, 73/23/EEC
Mode of action	Type 1 (EN60730-1)
Software class	A (EN60730-1)
Maintenance	Maintenance-free
Weight	680 g

B24C – Communication module

Application

SLC technology
The BC 24 module is used for the control of damper actuators
Power supply and communication are implemented with an interchangeable two core cable, SLC24-16B system.
A thermoelectric release mechanism and a duct smoke detector can be connected without the need for additional devices

Use

B24C – BC24-G2 communication module from BV-Control AG

Description	B24C
Nominal voltage	From SLC® control module
Power consumption	1 W
Connections	Plug connections, screw terminals
Damper power supply	24 V
Ambient temperature	-20 to 50 °C
Storage temperature	-20 to 80 °C
Humidity	95 % rh, no condensation
Weight	255 g
B × H × T	114 × 153 × 54 mm
Max. impulse voltage	2.5 kV (EN60730-1)

B24D, B230D – Communication module

Application

AGNOSYS system
BRM-F-ST module is used for the monitoring and control of smoke control dampers
Up to 126 modules can be connected in a ring topology

Use

B24D – AGNOSYS BRM10FST communication module
B230D – AGNOSYS BRM10F communication module

Description	B24D/B230D
Nominal voltage	18 – 32 V DC (typically 24 V)
Connections	Plug connections, screw terminals
Damper power supply	24/230 V AC 24 V DC
Ambient temperature	0 to 45 °C
Humidity	90 % rh, no condensation
Weight	510 g
B × H × T	158 × 180 × 65 mm

L [mm]

Length of the smoke control damper

B [mm]

Width of the smoke control damper

H [mm]

Height of the smoke control damper

qv [m³/h]; [l/s]

Volume flow rate

LWA [dB(A)]

A-weighted sound power level of air-regenerated noise for the smoke control damper

A [m²]

Free area

Δpt [Pa]

Total differential pressure

v [kg]

Airflow velocity based on the upstream cross section (B × H)

Downloads

product information

Print page Type EK-JZ
Product data sheet Type EK-JZ

EK-JZ_PD_2021_07_09_DE_en Product data sheet 1,2 MB pdf
TROX UK Fire Damper and Smoke Control Damper Selection Guide (11/08/21)v2

3,5 MB pdf

brochures

Universal. Modular. Safe. - Smoke extraction - EK-KZ

SF_2021_08_EK-JZ_DE_en_web Sales Flyer 770 KB pdf

certificates

Declaration of performance Type EK-JZ

EK-JZ_DoP_2021_07_DE_en Declaration of performance 310 KB pdf

operation manuals

Fire Safety - Promatect LS suppliers UK – Smoke Control Dampers

140 KB pdf
Installation and operating manual Type EK-JZ

EK-JZ_IOM_A00000062392_V6_2021_07_GB_en 4 MB pdf

EK-JZ

For mechanical smoke extract systems and pressure differential systems, as well as for providing additional supply air

General information

Technical information

Function, Quick sizing, Specification text, Order code

Dimensions, Product details

Accessories, Attachments 1&2, Technical data, Building Management System (BMS), Nomenclature

Accessories

ATTACHMENTS 1

Attachments 2

Wiring examples, Technical data

Downloads

product information

Print page Type EK-JZ

Product data sheet Type EK-JZ

TROX UK Fire Damper and Smoke Control Damper Selection Guide (11/08/21)v2

brochures

Universal. Modular. Safe. - Smoke extraction - EK-KZ

certificates

Declaration of performance Type EK-JZ

operation manuals

Fire Safety - Promatect LS suppliers UK – Smoke Control Dampers

Installation and operating manual Type EK-JZ

TROX SERVICES