Non-return damper, variant KUL-G

Bearings

Casing and duct connection

Type KUL

For installation into ductwork

Non-return dampers prevent unwanted airflows against the intended airflow direction when the system is not in operation

Maximum differential pressure: 100 Pa
Casing with U-channel connection suitable for rectangular ducts
Available in standard sizes and many intermediate sizes
Non-return damper with formed aluminium blades for normal requirements; blades are fitted with seals for sound attenuation

Optional equipment and accessories

Installation subframe
Powder coating (RAL or DB)

Application

Application

Type KUL non-return damper for installation into ductwork
Prevention of unwanted airflows against the intended airflow direction when the system is not in operation
Blades close automatically when the system is shut down
Maximum differential pressure 100 Pa

Special characteristics

Any intermediate sizes within the standard size range are available
operating temperature: –20 – 80 °C
Maximum differential pressure: 100 Pa
Non-return dampers are opened and closed by the airflow; no actuator is required
Non-return damper with formed aluminium blades for normal requirements; blades are fitted with seals for sound attenuation

Nominal sizes

B: 200, 400, 600, 800, 1000, 1200, 1400, 1600 mm (intermediate sizes: 201 – 1599 mm in increments of 1 mm)
H: 215, 315, 415, 515, 615, 715, 815, 1015, 1215, 1415, 1615 mm (intermediate sizes: 216 – 1614 mm, in increments of 1 mm)
Any combination of B × H

Description

Variants

KUL: Non-return damper, duct connection without flange holes
KUL-G: Non-return damper, duct connection with flange holes

Parts and characteristics

Casing
Blades with low-friction bearings
Blade restrictors
Blade tip seals
Bottom travel stop (angle section)
Visible mullion from B = 997 mm

Accessories

Installation subframe: Installation subframe for the fast and simple installation of mechanically self-powered dampers

Construction features

Casing, material thickness 1.25 mm
Blades, material thickness 1.0 mm
Flanges on both sides, suitable for duct connection
Additional side bar with fixing holes to accommodate the blade shafts and integral blade restrictors (pins)
Blade restrictors prevent the blades from opening beyond a certain angle

Materials and surfaces

Casing, mullion and travel stop (angle section) made of galvanised sheet steel
Blades made of formed aluminium
Blade shafts made of brass
Side bar made of PVC plastic
Blade tip seals made of foamed polyester
Blade restrictors made of plastic

Maintenance

Maintenance-free as construction and materials are not subject to wear
Contamination should be removed as it may lead to corrosion and to increased closed blade air leakage

Technical information

Function, Technical data, Quick sizing, Specification text, Order code, Related products

Schematic illustration of KUL 00106691_0.

① Border
② Blades (closed)
③ Mullion from B = 997 mm
④ Blades (open)
⑤ Blade restrictor
⑥ Seal

Functional description

Non-return dampers open and close automatically.

When the system is in operation, the blades open when air flows.

When the system is shut down, the blades close due to their weight. They safely prevent air from flowing against the intended airflow direction.

Nominal sizes	200 × 215 to 1600 × 1615 mm
Volume flow rate range	110 – 6460 l/s or 396 – 23256 m³/h at 2.5 m/s
Total differential pressure	25 Pa at 2.5 m/s
Maximum differential pressure in closing direction	100 Pa
Operating temperature	–20 to 80 °C

Quick sizing tables provide a good overview of the volume flow rates with an airflow velocity of 2.5 m/s. Intermediate values can be interpolated.

UL, KUL: Width 200 – 600 mm, volume flow rate at 2.5 m/s

H	B [mm]
H	200		300		400		500		600
mm	l/s	m³/h	l/s	m³/h	l/s	m³/h	l/s	m³/h	l/s	m³/h
215	110	396	160	576	215	774	270	972	325	1170
315	160	576	235	846	315	1134	395	1422	475	1710
415	210	756	310	1116	415	1494	520	1872	625	2250
515	260	936	385	1386	515	1854	645	2322	775	2790
615	310	1116	460	1656	615	2214	770	2772	925	3330
715	360	1296	535	1926	715	2574	895	3222	1070	3852
815	410	1476	610	2196	815	2934	1020	3672	1220	4392
1015	510	1836	760	2736	1020	3672	1270	4572	1520	5472
1215	610	2196	910	3276	1220	4392	1520	5472	1820	6552
1415	710	2556	1060	3816	1420	5112	1770	6372	2120	7632
1615	810	2916	1210	4356	1620	5832	2020	7272	2420	8712

UL, KUL: Width 800 – 1600 mm, volume flow rate at 2.5 m/s

H	B [mm]
H	800		1000		1200		1400		1600
mm	l/s	m³/h	l/s	m³/h	l/s	m³/h	l/s	m³/h	l/s	m³/h
215	430	1548	540	1944	645	2322	755	2718	860	3096
315	630	2268	790	2844	945	3402	1100	3960	1260	4536
415	830	2988	1040	3744	1250	4500	1450	5220	1660	5976
515	1030	3708	1290	4644	1550	5580	1800	6480	2060	7416
615	1230	4428	1540	5544	1850	6660	2150	7740	2460	8856
715	1430	5148	1790	6444	2150	7740	2500	9000	2860	10296
815	1630	5868	2040	7344	2450	8820	2850	10260	3260	11736
1015	2030	7308	2540	9144	3050	10980	3550	12780	4060	14616
1215	2430	8748	3040	10944	3650	13140	4250	15300	4860	17496
1415	2830	10188	3540	12744	4250	15300	4950	17820	5660	20376
1615	3230	11628	4040	14544	4850	17460	5650	20340	6460	23256

Differential pressure

v	Δp_t
m/s	Pa
0.5	10
1	15
2	20
3	25
4	30
5	40
6	45

Rectangular non-return dampers to prevent air from flowing against the intended airflow direction; for installation into ductwork.

Ready-to-install component which consists of a casing, blades with low-friction bearings, and travel stop and sealing parts.

Special characteristics

Any intermediate sizes within the standard size range are available
operating temperature: –20 – 80 °C
Maximum differential pressure: 100 Pa
Non-return dampers are opened and closed by the airflow; no actuator is required
Non-return damper with formed aluminium blades for normal requirements; blades are fitted with seals for sound attenuation

Materials and surfaces

Casing, mullion and travel stop (angle section) made of galvanised sheet steel
Blades made of formed aluminium
Blade shafts made of brass
Side bar made of PVC plastic
Blade tip seals made of foamed polyester
Blade restrictors made of plastic

Technical data

Nominal sizes: 200 × 215 to 1600 × 1615 mm
Volume flow rate range: 110 – 6460 l/s or 396 – 23256 m³/h at 2.5 m/s
Total differential pressure: 25 Pa at 2.5 m/s
Maximum differential pressure in closing direction: 100 Pa
Operating temperature: –20 to 80 °C

Sizing data

V __________________ [m³/h]
Δp_st __________________ [Pa]

Air-regenerated noise

L_WA __________________ [dB(A)]

Type
KUL Non-return damper

Construction
No entry: duct connection without flange holes
G Duct connection, flange holes on both sides

Nominal size [mm]
B × H

Installation subframe
No entry: none
ER With (only KUL-G)

Surface
       No entry: standard construction
P1       Powder-coated,        RAL CLASSIC colour
PS       Powder-coated, DB colour

       Gloss level
       RAL 9010 50 %
       RAL 9006 30 %
       All other RAL colours 70 %

Order example: KUL–G/600×1200

Construction	Duct connection, flange holes on both sides
Nominal size	600 × 1200 mm
Installation subframe	Without
Surface	Standard construction

Accessories

Type Installation subframe

Dimensions and weight, Product details

KUL

B: 200 – 1600 mm, intermediate sizes 201 – 1599 in increments of 1 mm
H: 215 – 1615 mm, intermediate sizes 216 – 1614 mm in increments of 1 mm
The weight for the next larger size applies

Flow cross section to calculate the airflow velocity

A = B × H

Unit of measure for B and H: m

KUL: Weights

H	B [mm]
H	200	300	400	500	600	800	1000	1200	1400	1600
mm	kg
215	2	3	3	4	4	5	6	8	10	11
315	2	3	4	4	5	6	7	9	10	11
415	3	4	4	5	6	7	8	10	11	13
515	3	4	5	6	6	7	9	11	12	15
615	4	5	5	6	7	8	10	12	13	17
715	4	5	6	7	8	8	11	13	15	18
815	5	6	6	8	9	9	13	16	17	19
1015	5	6	7	9	10	11	15	18	19	20
1215	6	7	7	10	11	13	17	20	20	22
1415	6	7	8	11	12	15	18	21	22	24
1615	7	8	8	11	13	17	19	22	24	26

Flange holes – KUL 00146052_0

① Even number of holes (hole pitch = 150 mm)
② Uneven number of holes (hole pitch = 150 mm)

KUL: Width, no. of flange holes

Width	No. of holes
Width	n
mm	–
200 – 346	2
347 – 496	3
497 – 646	4
647 – 796	5
797 – 946	6
947 – 1096	7
1097 – 1246	8
1247 – 1396	9
1397 – 1546	10
1547 – 1600	11

KUL: Height, no. of flange holes

Height	No. of holes
H	n
mm	–
215 – 362	2
363 – 512	3
513 – 662	4
663 – 812	5
813 – 962	6
963 – 1112	7
1113 – 1262	8
1263 – 1412	9
1413 – 1562	10
1563 – 1615	11

Installation details, Basic information and nomenclature

Installation into an internal wall, without installation subframe

Installation and commissioning

Horizontal airflow: Vertical installation
Vertical airflow: Installation into ducts with an upward airflow; horizontal installation
Straight upstream section required (at least B + H) on the positive pressure side of fans
Ensure a gradual start-up of fans to avoid a sudden pressure increase
Only for installation in internal spaces
For external walls the damper should be combined with a Type WG-KUL external weather louvre

Nomenclature

L_WA [dB(A)]

A-weighted sound power level of air-regenerated noise for the mechanically self-powered damper

A [m²]

Upstream cross section

v [m/s]

Airflow velocity based on the upstream cross section

V [m³/h] and [l/s]

Volume flow rate

Δp_st [Pa]

Static differential pressure

Δp_t [Pa]

Total differential pressure

All sound power levels are based on 1 pW.

Principal dimensions

B [mm]

Duct width

H [mm]

Duct height

n [ ]

Number of flange screw holes

m [kg]

Weight

Downloads

product information

Print page Type KUL
Product data sheet Type KUL

Product data sheet 820 KB pdf

certificates

Declaration of conformity or declaration of incorporation Type KUL

Declaration of conformity or declaration of incorporation 130 KB pdf

operation manuals

Installation manual Type KUL

2018/10/A00000053072 Installation manual 440 KB pdf

TROX Services

Product search A-Z Find out quickly and simply.

TROX Easy Product Finder Fast. Reliable. Innovative.